Specifications

Weight of Drone (Without Battery): 
120g
Takeoff Weight: 
165g
Dimension Frame: 
153*153*70mm
Diagonal Length: 
110mm
Material Frame: 
Carbon Fiber
Shell Material: 
Body protective case: TPE with fine matte finish;
Camera and Battery Fixing Part: ABS and PC fine matte finish
Full-Coverage Propeller Guards: 
Nylon + fiber + polished finish
Body Color:
The default factory color is gray; other available options include Orange, Black, and Pink
Flight Time: 
7 Minutes
Ascent Speed:
50km/h
Horizontal Speed(at sea level, no wind): 
110km/h
Flight Distance: 
2000 meters, maximum range is tested in an unobstructed area free of interference
Max Service Ceiling Above Sea Level: 
Same as the flight distance, the flight distance and height can be set as you need in GeoFence of Mission Planner
Maximum Wind Resistance: 
Moderate breeze
Flight Modes: 
It is default with Pos-Hold Mode, Alt-Hold Mode, Stabilize Mode, and Turtle Mode
Low Voltage Alarm:
If the voltage drops below 6.8V, the flight controller's red light will flash rapidly.
Positional Accuracy: 
20 centimeters
Operating Temperature:
-30℃~85℃

Aircraft

Motor:
SZ-SPEED 1303-10000KV Motor
Flight Control System: 
Radiolink All-In-One Flight Controller ArduBeta_aio with 4-in-i ESC and OSD module integrated
Battery: 
Gensace 2S 850mAh 35C XT30 Battery  
Propeller:
Gemfan 2512 Propellers

Power System

Flight Controller Specifications

Weight &  Dimension
Dimension
25.4 x 25.4mm
Weight
11.5g
Hardware
Processor
STM32F405RGT6
Sensor
Gyro
BMI270
Barometer
SPL06
Blackbox
128MB
OSD Module
AT7456E
Connector
Channel Output
M1 - M4
USB Port
Micro USB/Type-C
UART Port
4
PWM Output Solder Pad(CH5, 6)
Support
RC IN(Receiver with SBUS) Connect Port
1
CROSSFIRE IN(TBS CROSSFIRE Long-range Module)
1
ELRS Receiver Connect Port
1
Video Transmission Connect Port
1
Solder Pad(for 5V/12V Video Transmission)
1
Camera Port
1
I2C+GPS Port Connect Port
1
Optical Flow Connect Port
1
LED Indicator Light
Support
Solder Pad(for Buzzer)
1
Power Supply
Input Voltage
6.8-12.6V(2S-3S LiPo Battery)
BEC
5V/3A
Onboard 4-in-1 ESC
Support
Integrated ESC Current
20A
Firmware
Type
APM
Name
Ardubeta_aio_v1
Transmitter: 
Radiolink 8 channels transmitter T8S
Receiver:
R16SM
Frequencies Band: 
2.4GHz ISM(2400MHz~2483.5MHz）
Transmission Power: 
<100mW(20dBm)
Control Distance:
2000 meters, maximum range is tested in an unobstructed area free of interference

Remote Control System

Optical Flow: 
Optical Flow and Laser Two-in-one Module
Operating Voltage: 
3.7～5.0V
Operating Current:
≤70mA
TOF FOV: 
HFOV: 20°; VFOV: 17°
Operating Temperature: 
-20 to 60°C
Measurement Distance: 
4 meters indoors/ outdoors
Light Source Wavelength: 
940nm
Optical Flow FOV: 
Horizontal/Vertical: 30°
Frame Rate: 
50Hz
Ambient Illumination: 
>20Lux
Maximum Measurement Speed:
7m/s at a height of 1 meter

Positioning System

Charger: 
Radiolink CM210
Charging Input: 
DC 5V
Charging Current: 
1A@5V/2A@5V
Compatible Battery:
only for 2S LiPo battery

Charger System

Model: 
ZENCHANSI BROWN BEAR 008
Communication Frequency: 
5.725-5.850GHz
Power: 
500mW/200mW/600mW/Power off(PitMode)
Current(12V): 
350mA(50mW)/510mA(200mW)/750mA(600mW)
Input Voltage: 
7-24V DC
Antenna: 
MMCX ANT
Dimension:
27*27*4.8mm(1.06"*1.06"*0.19")

Analog Video Transmission

Video Transmission

Model: 
Caddx sable camera
Sensor: 
1/3” Inch Starlight Sensor
Resolution: 
1200TVL
FOV: 
130°(4:3) / 165°(16:9)
Image:
4:3 & 16:9(Switchable)
Min. Illumination: 
0.001LUX
Wide Power Input: 
5-27V
Working Temperature:
-20°C ~ +60°C
Weight: 
5.9g
Dimension:
19*19*20mm

Camera

Model: 
EWRF 3.0 Inches FPV Goggles
Communication Frequency: 
5.362-5.945GHz
Resolution: 
480*272
Display Ratio:
16:9
Brightness:
230cd/m²
Video Formats: 
NTSC/PAL
Power Adapter: 
DC 5V/1.5A (USB interface)
Battery:
3.7V/1800mAh, each full charge revive around 3.5hr working time
Working Time:
3.5 hours

Goggles(Can Be Selected)

Model: 
Hawk eye all-in-one 4.3 inch FPV Monitor
Resolution: 
480*3(RGB) *272
Backlight: 
LED
Brightness: 
500 cd/m2
Aspect Ratio: 
16:9
Response Time: 
10ms
Color System: 
PAL/NTSC
Working Time: 
About 2.5 hours
Input Signal: 
Video  (PAL/NTSC)
Output Signal: 
Video
Antenna Interface: 
RP-SMA
Sensitivity:
-94db

FPV Monitor(Can Be Selected)